Showing 20 2 post lifts

Buying Advice

Choosing a 2-post car lift

A 2-post car lift, often called a 2-post ramp, raises a vehicle by its chassis so the wheels hang free. This leaves the brakes, suspension, exhaust and tyres accessible. Before choosing a model, check your ceiling height, the floor, the arms, the lift capacity and the power available in your workshop.

Clearfloor or floorplate

On a clearfloor lift, an overhead beam joins the columns and leaves the floor between them unobstructed. That leaves room to move transmission jacks, oil drainers and creepers under the vehicle. A floorplate lift, also called a baseplate lift, carries its hydraulic lines across a low plate on the floor instead, without an overhead beam.

The BendPak 10AP and 12APX are clearfloor lifts. The BendPak 9APF and 12APF, the Launch TLT240SBA-3 and the Space SDS32 are floorplate lifts. The overhead beam needs sufficient ceiling height.

Low ceilings and high-roof vans

For workshops with limited ceiling height, the BendPak 10AP-SRT and 12AP-SRT are short-rise floorplate lifts. For high-roof vans, the extended-height BendPak 10AP-168 and 10APX-181 have taller columns. Liftmaster checks the ceiling height, floor space and concrete during the site survey, before specifying a lift.

Symmetric and asymmetric arms

Symmetric arms centre the vehicle between the columns and suit vans and longer vehicles. Asymmetric arms position it further back, leaving more room to open car doors. BendPak's Bi-Metric arms work in either configuration, while the Ravaglioli KPH-45ECGA uses an asymmetric arm layout.

In the Nussbaum Smart Lift range, the 2.35 SL SC has low-profile arms for sports cars. The 2.35 SL EV uses EV-specific swing arms. Check the arm layout against the vehicles you service.

Lifting capacity

2-post vehicle lifts on this page range from the 3,000kg Nussbaum Smart Lift 2.30 SL DT to the 5,500kg Space SDH370.55LIKTA. Choose a capacity that covers the heaviest vehicle your workshop handles. The Nussbaum Smart Lift 2.30 SL DT is rated for cars.

The 4,536kg BendPak 10AP is rated for cars, SUVs and up to medium wheel base vans. The 5,443kg BendPak 12APX is rated for up to long wheel base vans. Check both the capacity and the vehicles each model is intended to lift.

Single-phase or 3-phase power

Check whether your workshop has single-phase or 3-phase power before choosing a lift. Several BendPak 2-post lifts run on a single-phase supply. Launch lifts come in single-phase and 3-phase versions: a model code ending -1 is single-phase and one ending -3 is 3-phase. The Nussbaum, Space and Ravaglioli models in this range run on 3-phase.

Each product page lists the required power supply. Use the Power Supply filter above to narrow the range to models your workshop can run.

Installation and Service

2-post lifts supplied and fitted

Every 2-post lift from Liftmaster comes with delivery, installation and a 2-year parts and labour warranty as standard. The lift is anchored to the floor, so the concrete must meet the manufacturer's depth and strength requirements. Liftmaster checks the concrete during the site survey.

Liftmaster's engineers install and commission the lift to the manufacturer's specification, then hand it over with LOLER certification. Planned maintenance contracts and a direct breakdown line are available after installation. See installation and servicing.

BendPak

BendPak 2-post lifts from the sole UK distributor

Liftmaster is the sole UK distributor for BendPak. The BendPak 2-post lifts in this range cover the 9APF, 10AP, 10AP-168, 10APX, 10APX-181, 12APX, 12APF and the short-rise 10AP-SRT and 12AP-SRT.

Each AP series lift uses the Automatic Swing Arm Restraint System, which holds the arms in place once the vehicle is lifted. See the full BendPak range.

Lift Types

2-post, 4-post or scissor lift

A 2-post lift raises the vehicle by its chassis, leaving the wheels free for brake, suspension, tyre and exhaust work. A 4-post lift is drive-on and supports the vehicle on its wheels. It is quicker to load and suits MOT testing, wheel alignment and parking.

A scissor lift takes up the least floor space and suits tyre bays and bodyshops. Workshops that handle different types of work may use more than one type of lift.

2-post lift guides

View All Guides

2-post car lift questions

Are 2-post car lifts safe?

Yes, provided the lift is installed to the manufacturer's specification, the correct vehicle lifting points are used and the lift is examined under LOLER. Liftmaster's engineers install every 2-post lift and hand it over with LOLER certification. BendPak AP series lifts also have an Automatic Swing Arm Restraint System that holds the arms in place under load.

Is installation included with a 2-post lift?

Yes. Every 2-post lift from Liftmaster includes delivery, installation by Liftmaster's engineers and a 2-year parts and labour warranty. Before installation, Liftmaster surveys the site to check the floor, ceiling height and power supply.

Which 2-post lifts run on a single-phase supply?

Several BendPak 2-post lifts run on a single-phase supply. Launch models ending -1 are single-phase and those ending -3 are 3-phase. The Nussbaum, Space and Ravaglioli models in this range require 3-phase power. Check the power supply listed on each product page, or use the Power Supply filter to see the lifts that match your workshop's supply.

How much ceiling height does a 2-post lift need?

The required height depends on the lift and the vehicles you service. A clearfloor lift needs space for its overhead beam, while a floorplate lift needs room for the vehicle at full lift height. The BendPak 10AP-SRT and 12AP-SRT are short-rise models for low ceilings. Liftmaster checks the measurements at site survey.

Can you install a 2-post lift outside?

Only a small number of 2-post lifts are approved for outdoor installation, and suitability depends on the exact model and manufacturer. BendPak states that all of its 2-post lifts are approved for indoor installation and use only. Speak to Liftmaster before planning an outdoor installation.

Can you store a car on a 2-post lift?

For storing a car, Liftmaster recommends a 4-post parking lift, which supports the vehicle on its wheels, rather than a 2-post lift. Autostacker parking lifts are also available through Liftmaster Home Equipment.

Find the right 2-post lift for your bay

Send us your bay dimensions, ceiling height, power supply and details of the vehicles you work on. Liftmaster's team can then recommend a lift and arrange a site survey.

Submit an Enquiry